Kite Making Kits: Choosing One That Flies and Getting It in the Air
Building a kite and then watching it fly is one of the most satisfying small projects there is, especially with children. Kits make it easier by supplying cut materials and a tested design. But some kits fly well and some barely fly at all. This guide covers how to choose a kit, what to look for in the parts, how to build a kite that flies straight, and how to get it up on its first day.
Choosing a kit
Pick a forgiving design
- Sled kites are the easiest to build: a sheet of plastic or paper with two or three sticks taped along it and a two-leg bridle. They fly in a moderate breeze and need no tail.
- Delta kites are a little more work but fly in lighter wind and sit at a steeper angle.
- Diamond kites are traditional and educational, but a flat diamond needs a well-made tail to fly steadily.
- Box kites are rewarding but fiddly; better as a second project.
Look at the parts
- Sail: ripstop nylon or polyester lasts; plastic film is fine for a first kite; paper tears quickly in damp or gusty weather.
- Spars: straight wooden dowels, bamboo, fibreglass or carbon. Check they are straight and of even thickness.
- Line: many cheap kits include a very short, weak line. Plan to replace it.
- Instructions: clear diagrams and bridle measurements matter more than decoration.
Match it to the builder
Younger children manage sleds and pre-printed plastic kits with an adult's help. Older children and adults can tackle deltas, diamonds and box kites with sewn or taped sails.
Building a kite that flies straight
Most kit kites that fly badly are lopsided. Symmetry is everything:
- Centre the spine. Mark the centre line of the sail and keep the spine exactly on it.
- Match both sides. Both halves of the sail, both spars and any wingtip pieces should be equal in length and weight.
- Balance test. Hold the finished kite by the centre of the spine near the bridle point; it should hang level, not dip to one side. Add a small piece of tape to the light side if it does.
- Bridle lengths. Measure the bridle legs exactly as the instructions say. A difference of a centimetre makes the kite pull to one side.
- Tension. The sail should be taut but not distorted. A wrinkle on one side makes the kite turn.
- Tail. For diamonds, a tail several times the kite's length adds stability. A longer tail fixes a spinning or looping kite.
Choosing line for a home-built kite
Home-built kites are usually small. The Kite Line Tension Calculator estimates that a 0.5 m² kite pulls about 0.7 kgf in 10 knots and 1.7 kgf in 15 knots, and suggests minimum breaking strengths of 3 kgf and 5 kgf. Plain polyester or cotton line of that strength or more is ideal. Never use glass-coated or metal "manja" line, which is dangerous and banned in many places.
A 30 to 50 m line on a winder is enough. It keeps the kite low enough to bring down quickly and well inside height limits; 50 m of line at 45 degrees puts a kite about 35.4 m up on our Kite Altitude Calculator.
The first flight
Pick the wind
Choose a steady gentle breeze, Beaufort force 3 (7 to 10 knots, 8 to 12 mph) on our Beaufort Scale Guide: leaves and small twigs moving, light flags extended. Under about 5 knots most kit kites will not stay up; in force 5 (from about 17 knots) light home-built kites are likely to break.
Pick the place
An open field or beach with no power lines, roads, trees or buildings nearby, and nobody downwind.
Launch and adjust
- Have a helper hold the kite 15 to 20 m downwind, facing you, while you hold the winder with your back to the wind.
- On your signal, the helper lets go and you pull in a few arm lengths of line; let line out as the kite climbs.
- If it spins or loops, lengthen the tail or check symmetry.
- If it will not climb and hangs low, move the bridle towing point slightly; the instructions usually show which way.
- If it dives to one side, check the bridle lengths and sail tension on that side.
Learning from the kite
A home-built kite is a good way to see physics in action. Try flying it in different winds and notice how much harder it pulls as the wind rises; the calculator shows why, since pull grows with the square of wind speed. Measure the line angle with a phone and estimate the kite's height. Compare it with a shop-bought kite of similar size.
How hard a kit kite pulls
Kit kites are small, and their pull is gentle. The Kite Line Tension Calculator gives:
- A 0.3 m² kite (a typical small sled or diamond): about 0.3 kgf at 8 knots and 0.6 kgf at 12 knots, with suggested line of 1 to 2 kgf.
- A 0.5 m² kite: about 0.5 kgf at 8 knots and 1.1 kgf at 12 knots (suggested 2 to 4 kgf).
- A 0.7 m² kite: about 0.7 kgf at 8 knots and 1 kgf at 10 knots (suggested 2 to 4 kgf).
So almost any sound kite line is strong enough. For a home-built kite the bigger risk is line that is too heavy: thick line sags and drags a light kite down. Choose the lightest plain line comfortably above those figures.
Height comes quickly even on a short line. On the Kite Altitude Calculator, 30 m of line at 50 degrees puts a kite about 23 m up, and at 60 degrees about 26 m. That is plenty for a first flight and easy to wind in.
To read a forecast for a kit kite, convert it on the Wind Speed Converter. A 10 km/h forecast is 5.4 knots, force 2: enough for a light sled or delta, marginal for a heavier diamond. 15 km/h is 8.1 knots, force 3, which suits almost every kit kite.
For a young child holding the line, those numbers are reassuring: even a 0.5 m² kite at 12 knots pulls only about 1.1 kgf. The thing to watch is not the pull but the line itself, so teach them never to wrap it around a hand.
Safety
- If the kite touches a power line, let go and tell an adult or the electricity company. Never try to retrieve it.
- Do not fly in wet weather or with thunder about.
- Wear gloves if the pull is firm, and never wrap line around a hand.
- Keep sharp tools away from young builders and supervise any cutting.
Our guide to family kite flying has more on picking a safe field and flying with children.